Grub updating single guy online dating profile examples

I had previously been using unetbootin to create the image for the install. Disk /dev/sdb: 7.7 Gi B, 8242855936 bytes, 16099328 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x17fcad22 Device Boot Start End Sectors Size Id Type /dev/sdb1 * 64 5898239 5898176 2.8G 17 Hidden HPFS/NTFS /dev/sdb2 5898240 5899647 1408 704K 1 FAT12 Disk /dev/loop0: 2.6 Gi B, 2779897856 bytes, 5429488 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes @Arcaici Instead of writing (hd0,gpt6) there, write the actual name of your partition. I have a problem I got stuck in umount /mnt/sys It says umount : /mnt/sys: target is busy So, i started to skip umount /mnt/sys But when in the last command umount /mnt it says target is busy too In step mkdir /mnt/boot/efi says Cannot create directory *** file exists, when i started reboot, still no grub kali show, directly to the windows @stellarix I've again run those commands and the entry of grub has been successfully added in my boot menu options.I found Rosa Image Writer, and I was able to install Kali without any issues. I have a laptop were i installed windows 10(it came with windows 8), and I am trying to install Kali 2017.2. Create a bootable (Kali 2017.2) USB using u Netbootin, this worked and I get the live, live persist etc. Partition my harddrive in Windows so that I have 100 GB unallocated space. Run ls to list the name of all partitions and show the output here. Yeah, the entry was removed when i did a firmware update so i again added it.

File exists But I still continued and then got stuck at the grub-install step.Click on the interface drivegrubx64Once kali boots open terminal and enter these commands sudo grub-install /dev/sda sudo update-grub For DELL users, there is no Boot from EFI option in your boot menu options but if you go to your UEFI settings you can add entry of bootloader in boot menu options. I think grub no longer remembers that partition in which kali filesystem is. Typing the settings in here brought me back to the grub prompt I've mentioned in my earlier posts. I have different disks for Windows and for the Linux I'm trying to install.I do not have Windows installed on my HP laptop, only Kali. For that run these commands: ls set root=(hd0,gptx) set prefix=(hd0,gptx)/boot/grub insmod normal normal ls(LS) lists all the partitions of your hard drive like this (hd0) (hd0,gpt1) (hd0,gpt2). Go to /mnt/EFI/kali and replace the grubx64with the one present in this zip file. I appreciate the time you've taken to try and help me with this. I have Kali installed on a VM on my Windows computer, so I'm ok. In my case, Linux partitions are /dev/sdi1, 2 and 3.Also the mount --bind /dev /mnt/dev says it cant find mount point /dev when I mount all partitions to /mnt.Through a bunch of research I found it makes a difference how you setup your USB disk to install Kali.

Search for grub updating:

grub updating-18grub updating-4

I read all the replies here and my laptop specs are a lot similar.

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “grub updating”